Emmcdl

To build emmcdl with Autoconf 2.69 and Automake 1.15:

cd <to-source-dir>

$ aclocal $ autoconf $ automake --add-missing

$ ./configure

$ make

emmcdl linux binary in .(<source-dir>)

$ emmcdl Version 2.10 Usage: emmcdl <option> <value> Options: -l List available mass storage devices -info List HW information about device attached to COM (eg -p COM8 -info) -MaxPayloadSizeToTargetInBytes The max bytes in firehose mode (DDR or large IMEM use 16384, default=8192) -SkipWrite Do not write actual data to disk (use this for UFS provisioning) -SkipStorageInit Do not initialize storage device (use this for UFS provisioning) -MemoryName <ufs/emmc> Memory type default to emmc if none is specified -SetActivePartition <num> Set the specified partition active for booting -disk_sector_size <int> Dump from start sector to end sector to file -d <start> <end> Dump from start sector to end sector to file -d <PartName> Dump entire partition based on partition name -d logbuf@<start> <size> Dump size of logbuf to the console -e <start> <num> Erase disk from start sector for number of sectors -e <PartName> Erase the entire partition specified -s <sectors> Number of sectors in disk image -p <port or disk> Port or disk to program to (eg COM8, for PhysicalDrive1 use 1) -o <filename> Output filename [<-x <.xml> [-xd <imgdir>]>...] Program XML file to output type -o (output) -p (port or disk) -f <flash programmer> Flash programmer to load to IMEM eg MPRG8960.hex -i <singleimage> Single image to load at offset 0 eg 8960_msimage.mbn -t Run performance tests -b <prtname> <binfile> Write <binfile> to GPT <prtname> -g GPP1 GPP2 GPP3 GPP4 Create GPP partitions with sizes in MB -gq Do not prompt when creating GPP (quiet) -r Reset device -ffu <.ffu> Download FFU image to device in emergency download need -o and -p -splitffu <*.ffu> -o <xmlfile> Split FFU into binary chunks and create rawprogram0.xml to output location -protocol <s|f> Can be <s>(STREAMING), default is <f>(FIREHOSE) -gpt Dump the GPT from the connected device -raw Send and receive RAW data to serial port 0x75 0x25 0x10 -wimei <imei> Write IMEI <imei> -v Enable verbose output

Examples: emmcdl -p ttyUSB0 -info emmcdl -p ttyUSB0 -gpt emmcdl -p ttyUSB0 -SkipWrite -SkipStorageInit -MemoryName ufs -f prog_emmc_firehose_8994_lite.mbn -x memory_configure.xml emmcdl -p ttyUSB0 -f prog_emmc_firehose_8994_lite.mbn -x rawprogram0.xml -SetActivePartition 0 emmcdl -p ttyUSB0 -f prog_emmc_firehose_8994_lite.mbn -x rawprogram0.xml -xd imagedir -SetActivePartition 0 emmcdl -p ttyUSB0 -f prog_emmc_firehose_8994_lite.mbn -ffu wp8.ffu emmcdl -p ttyUSB0 -f prog_emmc_firehose_8994_lite.mbn -d 0 1000 -o dump_1_1000.bin emmcdl -p ttyUSB0 -f prog_emmc_firehose_8994_lite.mbn -d SVRawDump -o svrawdump.bin emmcdl -p ttyUSB0 -f prog_emmc_firehose_8994_lite.mbn -b SBL1 c:\temp\sbl1.mbn emmcdl -p ttyUSB0 -f prog_emmc_firehose_8994_lite.mbn -e 0 100 emmcdl -p ttyUSB0 -f prog_emmc_firehose_8994_lite.mbn -e MODEM_FSG emmcdl -p ttyUSB0 -f prog_emmc_firehose_8994_lite.mbn -raw 0x75 0x25 0x10