TELEX EURORACK EXPANDERS

The TELEX are a family of eurorack expanders that were initially designed to interface with the Monome Teletype to provide additional inputs and outputs. Utilizing the II bus (i2c) and having a flexible command set, there is no reason that these modules couldn't connect and extend other Monome Eurorack devices (even non-Eurorack devices that support II like the Aleph) or your own hardware projects.

Follow the conversation at llllllll.

The Modules

The TELEXo (or TXo) is an output expander and the TELEXi (or TXi) is an input expander. They have little jumpers on the back so you can hook more than one of each module to your Teletype simultaneously. (Theoretically, up to eight of each type - though I’ve only tested six total modules at a time thus far. There will be a limit based on the II bus resistance - not sure what it is yet.)

TELEXo (TXo): a 4HP output module that provides 4 trigger outputs and 4 CV outputs addressable over II. Up to 8 can be independently addressed by the Teletype.
TELEXi (TXi): a 4HP input module that provides 4 control voltage potentiometers and 4 independent control voltage inputs. Up to 8 can be independently addressed by the Teletype.

TELEX MODULES

Teletype Firmware

We recommend the Teletype 2.0 BETA at this point. You can get it from this forum:

https://llllllll.co/t/teletype-2-0-beta-release-candidate-1-released-6th-june-2017/6939?u=bpcmusic

It is the bomb.

You can always head to Monome for the latest Official Teletype Firmware.

TELEX Firmware

Download the latest TELEX firmware from the releases section of this site:

https://github.com/bpcmusic/telex/releases

Installing Your Firmware

DO NOT POWER YOUR MODULE WHILE CONNECTING THE TEENSY VIA USB TO YOUR COMPUTER - THIS WOULD BE VERY BAD

Ok. With that out of the way, here are some simple steps.

Firmware is loaded on the Teensy processor that piggybacks on the underside of your module. Doing so is pretty simple.

Download the Teensy Loader application for your operating system from https://www.pjrc.com/teensy/loader.html (if you don't have it already)
Download and unzip the latest TELEX firmware from https://github.com/bpcmusic/telex/releases
(optional) Carefully remove the Teensy from your module
Connect the Teensy to your computer via USB
Use your operating system specific instructions for the Teensy Loader to open the appropriate firmware in the Teensy loader and program it on your Teensy
Disconnect the Teensy from USB when the firmware has been loaded
Reattach the Teensy to your module if you removed it
Party.

Compiling Your Own Firmware

Compiling the TELEX firmware is done using the Arduino Development Environment and a few extensions.

Several additional libraries are included in the project due to the Arduino IDE's wonderful linking capabilities.

IMPORTANT: overclock your Teensy 3.2 to 120 MHz in the IDE; Teensy 3.6 should be at 180 MHz

Critical Startup Optimization for Compilation

NOTE: this keeps changing in the Teensyduino application. I'm not finding this necessary anymore, but am leaving the old instructions in case anyone wants to fuss around with it. You can ignore for now.

If you want your TELEX to be ready when your Teletype has booted and is sending out the I script for the program that it is loading at startup, you need to make a change to the Teensy file "pins_teensy.c" in your Arduino hardware folder. For my mac, this is inside of the Arduino application package in:

Contents\Java\hardware\teensy\avr\cores\teensy3\pins_teensy.c

You need to change the values in the delay() calls - the original values are commented off to the right:

#if TEENSYDUINO >= 142
	delay(25);
	usb_init();
	delay(150); // 275
#else
	delay(50);
	usb_init();
	delay(125); // 350
#endif

For now, we edit this in-place. I know. We shuddered too. But, that seems to be the best way to make the change. Remember, you need to change it back for any other Arduino compilation you plan to do as it may have the device ready before all of your related components are - including the Teensy's USB interface.

TELEX Command Reference

Reference documents for the commands supported by the TXo and TXi are located here:

The documents are a little behind the latest firmware; we're moving all operator definitions into the 2.0 documentation system which is up to date.

The latests ops are mentioned in this forum post, if you are curious. You need the 2.0 beta firmware (mentioned above) to access them.

https://llllllll.co/t/telex-teletype-expanders/1379/609?u=bpcmusic

TELEXo

Each 4HP module adds 4 Trigger outputs and 4 Control Voltage outputs.

All Teletype output functionality is supported by the TXo. Operators are near-identical for basic functionality, just put a "TO.” in front of the set you already know. The outputs are a little different; the triggers are +5V triggers and the CV outputs are bipolar (-10V to +10v) with 16 bit resolution over that range.

Extended functionality of the TXo starts with being able to specify longer values for slew and pulse times (in seconds and minutes).

The TXo has the following “experimental” features for each of its four TR outputs:

Configurable pulse dividers for each output
Independent metronomes for each output that will pulse each output at intervals that can be set in milliseconds, seconds, minutes, and beats per minute (BPM)

The TXo also has the following “experimental” features for each of its four CV outputs:

a quantizer with a dozen or so microtonal scales in addition to equal temperament
an oscillator (not currently band-limited) that supports frequencies from LFO rates up to around 8kHz with variable morphing waveforms (sine, triangle, saw, variable width square, and noise), adjustable phase offset, and frequency slew (portamento)
an AR (attack + release) envelope generator with times in milliseconds, seconds and minutes

These extended features, when combined together, can really push the envelope of the TXo’s processor and do some crazy stuff. For example: the output's envelope generator can act as a VCA, which turns the expander into a little 4-voice synth.

TELEXi

Each 4HP module adds 4 IN jacks and 4 PARAM knobs.

The IN jacks are bipolar (-10V to +10V).
They jacks and knobs just like the Teletype IN and PARAM operators (TI.IN and TI.PARAM).
The TXi has some extended functionality where the TXi can do quantization for you and return note numbers against any one of its internal scales (there are about 12 or so).
Inputs are sampled with 13bit resolution.

Addressing Multiple TELEX Modules

Multiple TELEX modules are addressed using jumpers on the back of the unit. Theoretically, you can have up to eight of each type of unit on the same II bus. The addresses are non-conflicting between module types. For example, if you have one of each module, each would be unit #1 of that type and neither would have any address jumpers set.

The jumpers are oriented vertically and the rows are numbered from top to bottom:

Row 1
Row 2
Row 3

Placing jumpers on rows in the following sequence allows you to designate the unit # (which is the binary representation of the rows plus one). X indicates the placement of a jumper.

| Row 1 | Row 2 | Row 3 | Unit # | Inputs/Outputs | | --- | --- | --- | --- | --- | | 0 | 0 | 0 | 1 | 1-4 | | X | 0 | 0 | 2 | 5-8 | | 0 | X | 0 | 3 | 9-12 | | X | X | 0 | 4 | 13-16 | | 0 | 0 | X | 5 | 17-20 | | X | 0 | X | 6 | 21-24 | | 0 | X | X | 7 | 25-28 | | X | X | X | 8 | 28-32 |

DIY Tips and Warnings

The modules are made up with two boards stacked on top of each other and a Teensy 3.2 riding piggyback. They are primarily 603 SMD parts with a few 805, 1206 and SMD ICs thrown in for good measure. If you have assembled any of mxmxmx’s DIY modules (Ornament + Crime, Terminal Tedium, etc.) you should have no problem with the expanders. They are not, however, a beginners project for SMD.

The DAC that is used for the TXo is the DAC8564 (Mouser P/N: 595-DAC8564ICPW; datasheet: http://www.ti.com/product/DAC8564). This part is used by a number of Eurorack modules - including Mutable's Yarns and Ornament + Crime by mxmxmx. It has tiny little SMD legs that can cause DIY cursing. ;)

Use the Build Maps

The build maps are PDF files that have one page per component per side per board showing you all the places that component goes. This saves a ton of time and avoids the pain-in-the-ass component hunt. They are linked below - but check out the example below:

Build Map Sample

Thanks to c1t1zen for the idea. :)

Crazy Board Naming

I have a goofy naming convention for the boards. It is confusing. But, I embraced the organic silliness. The "Top" Board is the one behind the panel. The "Bottom" Board is the one facing the back of your case. The side of the board with the name of the unit and board on it is considered the "Top" of t

Telex

Install / Use

README